A Simple Varnish Finish 50% OFF!!

Rockler has my DVD on sale for 50% OFF right now. Normally $19.99, you can pick it up for only $9.99. I have no idea how many they have left in stock so you might want to act quickly! Wood Whisperer DVD: A Simple Varnish FinishWith so many finishing options, it can be hard [...]

Take a look at this blog about the psi turncrafter plus.

Get Bent! OK, I Will

Steam-bending wood is awesome, but I've never been a big fan of having a potential bomb in my house (or in the office). So I've worked at mastering cold-lamination bending, but I've found there's a lot of prep work (resawing, drum sanding, etc.), and the plastic resin glue is nasty stuff. It's the only glue that has ever gashed my arm.

So yesterday I pleased to see a big box propped up against my front door. Inside is a chunk of ash Compwood that I purchased from FlutedBeams.com. Compwood sounds like magical stuff – you can bend it cold, put it in your form and it retains any shape when it dries down to 6 or 7 percent moisture content.

There is no steam box. No plastic resin. Just cut the stuff and bend it.

How does it work? It is kind of like a flexible drinking straw. The wood is heated and then compressed along its length – so it's about 80 percent of its original length. This compresses the wood fibers like an accordion. As long as the wood is a little wet (20 to 25 percent MC), you can bend it in any plane. When it gets down to 12 to 14 percent MC, you can take it out of the form. When it reaches equilibrium, you can work it just like normal wood – rout it, plane it, glue it, sand it.

If you want technical details, including a manual on how to use the stuff for cabinetmaking, visit the official Compwood Products web site.

I'm going to be building a couple more Windsor chairs this summer, so I'm going to give the Compwood stuff a test run for the arms and the bows of the chairs. And I'll definitely post some video of the process.

— Christopher Schwarz

Other Wood Bending Resources to Investigate

• "The Complete Manual of Wood Bending" (Linden) Lon Schleining. It's a good introduction to the concepts of wood bending that I read years ago.

• The Ultimate Steam Box from The Windsor Institute. This is a nice system that we used to bend components during a chair class.

• February 2004 issue of Popular Woodworking. I wrote an article on cold laminations that I used to make an Eames coffee table.

• October 2005 issue of Popular Woodworking. Robert Lang demonstrates how to use cold bending to make contemporary shelves.

Find yourself a great general lathe online.

Ceramic studio change-over

There's an interesting difference between being a potter and being a woodworker that most people don't consider. Woodworkers switch materials all the time, from job to job. Right now, I'm working on a cherry piece, but the next one I'll start is in oak. There isn't a significant difference; the adhesives and finishes are much the same, and it's not as if I have to change my sawblade if I've switched wood. Just a little cleaning with the air compressor and the changeover is complete.

But clay poses a different problem. For the last six years, I've used a deep brown clay body called Black Mountain. I love the way it fires to a chocolate brown color. But just as all things must change, I've started mixing some new glazes, and the bottom line is - the glazes I like simply look better on a lighter clay. I'm switching to a buff stoneware called Long Beach, which I've thoroughly tested and find works perfectly for my glaze palette.

Now many potters switch back and forth, but to me - it's a hassle. That means I have to clean everything from my canvas mats to my throwing tools, to my wheel. And since there is such a drastic color difference in the two clays I use, the slightest cross contamination really pops out.

So it's with some sadness that I used the very last of my Black Mountain clay this week. I've probably gone through several thousand pounds of it; not much by most potter's standards, but for me, that's a fair amount. I threw three pieces - two small pitchers and a tumbler, on the wheel, as my final farewell.

And now the changeover begins! Time to pack away all the old glaze tests, using that clay body.

A clean wheel!

And clean tools!

The plaster molds needed a little scrubbing and organization.

And the glaze area needed some straightening out. There were all sorts of slips and unlabeled mixtures, all of which went into the trash.

As long as I've giving you a tour of my clay studio, here's something that most people ask about when visiting. Call me silly, but I save my cone packs. I just think they look cool.

And finally, my current sketch wall. Whenever I'm working on a project, I sketch it in full-size, or print it with my computer. At times, the wall can be crowded with dozens of drawings, but right now - the the new clay being introduced - most of the older drawings have been retired, and new ones are being added daily.

Hope you enjoyed the little tour!

Keep up to date with wood lathe updates.

INDICATING PARTS IN THE LATHE QUICKLY

Using appropriate ball bearing bolted to a piece of cold rolled makes indicating in the lathe a breeze!!

See Also : ±1±: My Bag Store !1#: Cheapest 7.1 Home Theater !#1 Navy Blazer Best Quality !1#: Pioneer Home Theater Speakers Immediately

Check out this great review of the Jet JWL 1220 wood lathe.

wooden bowl carving course

I have just finished a very enjoyable 3 day bowl carving course. These 8 bowls were carved by 4 course participants.

This was only the second bowl course I have run, the first was a great success with students making 2 bowls each and a fantastic standard of work. I was unsure though whether we were just lucky with a very talented group and whether future groups would do as well. One of the pleasures of running courses is the nice folk that come along and the camaraderie of all working and learning together. This time we had just 2 folk who had been on previous spooncarving courses and the others had done varying amounts of green woodwork from quite a bit to none at all. Everyone had lots of enthusiasm though.

We work by clamping a halved log in a holding device I call a bowlmate (plans to make one on the website) and the bowl is hollowed using an adze. I have tried all the available adzes and my favourite is made by Hans Karlsson in Sweden, they are not cheap but they work very well. It is possible to hollow the bowl with a gouge but much faster with an adze. After the adze we tend to smooth the surfaces with a gouge and curved knife.

After shaping the outside with an axe and pushknife final finishing with the curved knife again.

a

A little bit of refining the outside lines with a straight knife. I particularly liked Stephen's bowl with a ridge like a ships keel.

Carving this way is tremendously absorbing and we find it is important to stop every hour or so and have a walk around otherwise folk tend to get tired and that is when accidents happen.

And here are some finished bowls. Bowlcarving is a not quite as accessible as spooncarving in that you need to make a holding device and need a few more tools but it is tremendously rewarding and the results are beautiful and useful. Who wouldn't appreciate one of these bowls as a gift?

Check out this great review of the Jet JWL 1220 wood lathe.

wabi sabi

Very busy and behind with work at the moment but lots of interesting things which would be nice to share when I get time.

Today I just wanted to share a few thoughts on wabi sabi.

Ever since Bernard Leach went to Japan and wrote about Japanese aesthetics there has been great interest in the Japanese ideas about beauty. I was first introduced to the ideas through Leach's adaptation of Soetsu Yanagi's "The Unknown Craftsman". When I first read the book it was a revelation, it felt like it gave words to the feelings I already had, it gave a vocabulary to describe how simple humble things could be more wonderful than the glamorous and bling end of material culture that is often highlighted in Western museums and galleries. It suggested that the Japanese had words that explained these concepts which did not translate directly and had lots of subtle nuances difficult for outsiders to grasp but gives a fair explanation of the concepts in English.

"A certain love of roughness is involved, behind which lurks a hidden beauty, to which we refer in our peculiar adjectives shibui, wabi, and sabi."

Yanagi discusses shibui at length but suggests that wabi is to ephemeral a concept for most westerners to grasp. How tantalising a concept, not surprising then that wabi and sabi have become much used terms in the Western craft world even if we don't understand what they mean. We have this feeling that there is maybe something there that we admire, that if we could understand, would help us more fully understand the simple and humble in our own material culture. I suspect to some it also sounds rather grand using words that we don't fully understand in another language. There are numerous books on wabi sabi a typical one from my bookshelf is 'Wabi-Sabi for Artists, Designers, Poets & Philosophers". These are mostly written by Westerners trying to interpret what they think they have understood in the Japanese concepts for us. The above book is subtitled "Wabi Sabi is the quintessential Japanese aesthetic. It is the beauty of things imperfect, and incomplete. It is the beauty of things modest and humble." This actually sounds closer to the meaning of shibui than wabi or sabi to me though I have an incomplete understanding of all these words and prefer to use English terms which I understand fully.

The impetus for this post was what I think is a great blog post by a potter in Japan. Euan is a Westerner but he has lived and worked in Mashiko for 20 years (the pottery Village where Hamada lived and worked) This is the first paragraph of his post which I hope will encourage you to visit and read the rest, it is the simplest, clearest explanation of wabi sabi I have read, clearer and more comprehensive than most books on the subject.

"Just as in English there is a whole vocabulary available for the discussion of Art and Beauty, so too does such a vocabulary exist in Japanese. There is a tendency among people with a passion for and some experience in Japanese art to use the word “Wabi sabi”, and yet so little understanding of what the term refers to. Leonardo da Vinci said that, “If you cannot explain something, you don’t understand it.” To be anecdotal for a moment, there was one young American anthropologist who had studied pottery briefly in Mashiko, who gave a slide lecture here to coincide with an exhibition of American ceramics. Anything in his slides which seemed even vaguely Japanese influenced he described as possessing “Wabi sabi”. One of the thirty or so professional Japanese potters in the audience enquired, “What do you mean by Wabi sabi?” He laughed as he responded, “Nobody knows what Wabi sabi means!” The entire audience laughed also, but the young gentleman never realized that it was not because they agreed with him, but because of his naivety. Wabi sabi is not some mystical secret, but a basic aesthetic principal. Merely because he didn’t understand it doesn’t mean that it cannot be understood."

From Euan Craig's blog  11 may 2010

I would argue that we do not need Japanese words to understand these concepts, English is a remarkable language. What has been lacking in Western aesthetic discourse is an understanding of the humble, the simple. Perhaps the Shakers in the US came closest to this in the West. I remember in 1998 visiting the ethnographic museum in St Petersburg   This is a truly marvelous place, a grand imposing building, not unlike the British Museum or the V&A in London.

Inside are not the finest pieces of art and craft which form the material culture of the 1% at the top of society but the ordinary objects which formed the material culture of the 99% of Russian society. Where could I see the equivalent in the UK? Why do we always highlight the bling over and above the humble and the simple?

Save money on wood lathes for sale by shopping online!

DVD Review: Carving Swedish Woodenware

I first heard about the Carving Swedish Woodenware dvd (1990) from a blog post by Peter Follansbee and immediately contacted Drew Langsner about purchasing a copy.

Jögge Sundqvist packs a huge amount of information into one hour and shows you with complete clarity how to make a dough bowl and spoon using only hand tools.

First, he splits a log in two and explains why he chooses one half over the other for the dough bowl. Then, he uses his axe to create a flat surface on the convex side that will become the bottom of the bowl. He rough-shapes the inside with an adze and explains the proper tool grip and stance for maximum leverage.

Next, he uses gouges to finish the inside, then works the outside with an axe. Jögge talks during the entire film, explaining safe procedures, bowl design, and tool use.

When the outside of the bowl is shaped, he refines it at the workbench with spokeshave, drawknife, and plane.

I was surprised to see that he did not use a shaving horse. Instead, he worked the dough bowl on a workbench and tree stump and carved the spoons in his lap.

The second half of the film shows how to carve spoons. He shows two ways to rough out the shape: with a turning saw and with an axe. He explains what to look for when choosing a branch and how to shape the spoon for ease of use.

Always safety conscious, Jögge spends a lot of time explaining proper knife grips and how, by using these techniques, you cannot cut yourself.

He shapes the spoons with straight and crooked knives and gouges, and then shows how to carve decorative elements.

Jögge uses linseed oil (not boiled) on spoons and bowls for a natural finish.

The photo above shows all the tools you need if you'd like to make your own woodenware. And the first "tool" on your list should be Jögge's video. I cannot say enough good things about it.

You can find lots of good information on wood lathe tools here.

An American Girl Picnic Table

Being a woodworker is a wonderful thing. It seems at times as if nothing is out of our reach. Give us a little time, some wood, and inspiration and there is no telling what will materialize from our shops. So when a little girl who was fast approaching her 6th birthday asked [...]

Read all about wood lathe chucks!

Convince Your Family to Come to Cincinnati: Food

It took a fetus to convince me to come to Cincinnati in 1996. But I don't think you need to resort to such drastic measures (and perhaps painful surgery) to get your family in the car and on the road to Cincinnati next weekend for the Lie-Nielsen Hand Tool Event on June 4-5.

When most people think of Cincinnati, they think of the television show "WKRP," or perhaps they think of the Reds and maybe even the odd stuff we call chili here. (Side note: This is the only town in America where you can tell a waitress you want a "three-way" and not get slapped.)

But there's a lot more here. Enough, in fact, to make it a nice Spring getaway for the whole family. They can do fun stuff while you hang out with us at our offices at 4700 East Galbraith Road.

As long-time readers of my blog might know, I live for good food. So here (grudgingly) are the best places to eat in the city. If you have a spouse who is a foodie, here is how to make that person happy.

Boca: This is the the best restaurant in the city. Period. It is high-end American food, but it really defies categorization. Perfect service. Bold flavors. A beautiful restored space. It's a bit expensive, but I never regret spending it there. It's about 10 minutes from our offices.

Nada: This is the other restaurant owned by the chef who runs Boca. It's a downtown Mexican restaurant, but it's unlike any Mexican restaurant I've ever been to. Say it with me: Crispy pork belly tacos. Look over the menu and make a reservation immediately. It can be tough to get in.

Local 127: Another downtown restaurant, this one is focused on local ingredients. I think of it as down-home food with some upscale touches. Everything on the menu seems to have some pork in it (my highest compliment). Prices are reasonable for a downtown restaurant.

JoAn: This is a Japanese restaurant located in Toyota's North American headquarters near the airport. It is great sushi, with authentic seasonal specials. And lots and lots of Japanese. Because of Toyota, we have an embarrassment of good Japanese restaurants. A close second (in Newport, Ky., on the river) is Aoi.

Tucker's: I hate to tell you about this one. It's in a crummy neighborhood. It has been open since the 1940s and has never been remodeled. But it is a fantastic place for breakfast. The best goetta in town. Awesome pancakes. Home fries. And the people are just as good. It has been called the most integrated restaurant in our fair city. You'll eat with city councilmen and drug dealers, and they all get along at Tucker's.

Gordo's: Another place I give up grudgingly. This is the best place for craft beer and high-end burgers. Get there early to be sure you get a table. Don't be put off by the drab exterior, which screams "livers killed here." It's also about 10 minutes from our office.

Hugo: I am addicted to Lowcountry cusine – grits, shellfish, fried green tomatoes, fish. South Carolina stuff. This restaurant is the closest you'll get to Charleston, S.C., in the Midwest. It's a nice space. Good wine list. Close to our office.

Dewey's: I have a pizza problem. This is the best pizza in town (at this point -- more on that later). It's a small chain, and they have an outlet around the corner from our office. All the pizzas are great (each member of the staff has a favorite). Good beer. Good wine. Excellent house salad. I would eat there every week if I could.

Frieda's: This little bakery near our office is run by a German master baker. Everything I've tried there is incredible. The almond croissants. Macaroons. Butter cookies. This is the best bakery in a town filled with great bakeries.

I could go on for many more pages, but here is one last one.

Ambar: We have a lot of good Indian restaurants here in town, but this is the one that stands above the rest. A good choice for vegetarians (and meat lovers). This one is by the University of Cincinnati in a funky college neighborhood filled with art cinema, coffee houses and bookstores. It's a fun place to hang out.

I know I've skipped the usual suspects (Skyline Chili, Graeter's Ice Cream, LaRosa's), but you can find those anywhere.

— Christopher Schwarz

You can find lots of good information on wood lathe tools here.

Windsor Institute, Day 3

Do you like the look of the strapping doctor in the plaid shirt above? That's my dad. Today he learned about the power of a blog, and he just asked me if I could use it to find him an attractive female companion.

Me, I use the powers of the blog only for good (read: beer). I wouldn't use it to look for a meaningless (or meaningful) relationship. But hey, it is my dad. So bring it, ladies.

Today as we were drilling the holes in our seats to receive the spindles, a reader stopped by and dropped off a nice Belgian Trippel from Allagash (thanks Matthew!). My dad was a bit stunned.

"People just bring you beer?" he asked.

"Sometimes, yeah," I replied.

"Do you ask them to bring you beer?"

"No. But sometimes I mention that I like good beer. They do the rest."

I hope that the reason people bring me the occasional beer is that they are trying to do me a favor. And "favors" was definitely the theme of the third day of our class at The Windsor Institute.

We made a lot of progress on our chairs – we legged up, drilled holes for the spindles and stumps and we fit and shaped the arm. We also made a lot of mistakes – or we almost made mistakes. I was getting ready to drill a hole in my leg for a stretcher when Dan, a fellow student, stopped me short.

"Wrong way."

He was right. I was about to drill the hole in my leg at the exact opposite angle I needed. It would have been an embarrassing and time-consuming fix. But his two words saved me. And that was the scene the entire day – it was like an AA meeting on a tight wire over a pit of emaciated and perturbed piranhas. I caught at least two fatal errors before they happened. And everyone else had at least as many saves.

That's something that people don't really talk about much about woodworking classes. Working with other students keeps you on track, out of trouble and highly amused. It's a contrast to when I try to learn new things in the shop by myself. My progress is slower and riddled with false starts and dumb errors.

So tonight as I am sipping my Allagash Belgian ale and typing this, I am thankful for my fellow woodworkers. They keep me out of trouble in the shop during the day and in deep, barley-fueled trouble in the evenings.

— Christopher Schwarz

Other Woodworking Schools I Like

• Kelley Mehler School of Woodworking (kellymehler.com)

• Marc Adams School of Woodworking (marcadams.com)

• Northwest Woodworking Studio (northwestwoodworking.com)

Learn all about the Turncrafter Plus wood lathe.

Woodworking in America Registration is Officially Open

Yes, it was a few hours later than expected, and we're sorry. But registration is now officially open for Woodworking in America: The Ultimate Skill-Building Weekend, October 1-3 in Greater Cincinnati.

At the conference, you'll get expert instruction from such woodworking luminaries as Frank Klausz, Roy Underhill, Michael Fortune, Marc Adams, Jim Tolpin and more (including Christopher Schwarz).

You'll find classes in everything from cutting tenons by hand to tuning your bandsaw for precision work; from sharpening handsaws to router joinery. Plus, we've added design classes to this year's conference, and brought back the popular "SketchUp Hand-On Clinic" from last year's St. Charles event.

For a full list of classes and class descriptions, instructors, exhibitors, travel information and more – and to register – visit WoodworkingInAmerica.com. And if you register before August 2, you'll save $40 off the regular price.

— Megan Fitzpatrick

Save money on wood lathes for sale by shopping online!

Great Strides at White Water Shaker Village

The woodworkers who are restoring the White Water Shaker Village are making significant progress – just in time for the Woodworking in America tour of the village on Oct. 3.

Newly built and authentic windows are going in on the first floor of the Meeting House, which completely changes the appearance of the historic structure, both outside and in. The windows are walnut, just like the originals, and are being built using donations from the public (our magazine has sponsored construction of one of the windows).

Inside the meeting house, the restored wainscot is also changing the feeling of the entire first floor. All in all, the structure is beginning to feel a lot like the Shaker Meeting House at Pleasant Hill, which I visited last week. The open space. The nice woodwork. The windows that look out over a pastoral scene.

This fall, we'll be offering a guided tour of the White Water Shaker Village (which is not open to the public) for attendees of our Woodworking in America conference. We've chartered a bus to take about 50 attendees up to the village on the morning of Sunday, Oct. 3. The additional cost will be $15 – just enough to cover the bus rental.

While at the village, you'll get a guided tour of many of the structures curated by the Friends of White Water Shaker Village, a non-profit group that is devoted to restoring the village outside Cincinnati and opening it to the public. The volunteers are incredibly knowledgeable about Shaker life, construction and furniture – they've taught us a lot during the last year.

If you are attending Woodworking in America and are interested in the tour of White Water, be sure to sign up for it when you register for the conference. Registration for Woodworking in America opens in early May at woodworkinginamerica.com. Space will be limited on this tour. If demand is strong we might charter a second bus, but two buses will be the maximum number of people we can manage on the grounds.

— Christopher Schwarz

P.S. To read more about the White Water village, visit the organization's web site, or read this free online story I wrote or watch this video tour of the village shot by Drew DePenning.

Read detailed wood lathe reviews at Wood Lathes Online

Lie-Nielsen Hand Tool Event in Our Office

Quick – it is time to make up a quick excuse to your boss to arrange a sham business trip to Cincinnati on June 4-5. On those two days we are going to open wide the doors of our office and shop and host a Lie-Nielsen Hand Tool Event.

(If you need ideas for how to trick your boss into traveling here, let me know. We have a wide variety of businesses here. Just say "Procter & Gamble," "Kroger" and "Macy's.")

 Like the event last year, this one will be large. In addition to the Lie-Nielsen folks (including Thomas Lie-Nielsen himself), we'll have John Economaki here from Bridge City Toolworks, Kevin Drake from Glen-Drake Toolworks and Andrew Lunn from Eccentric Toolworks. Oh, and how could I forget the most awesome part: members of the Society of American Period Furniture Makers (SAPFM) are giving demonstrations on a wide variety of skills the entire two days.

Last year the SAPFM members demonstrated inlay, carving, design, moulding planes and lots of other stuff.

This year we are doing a couple things a little different. The show will be on Friday (4 p.m. to 9 p.m.) and Saturday (10 a.m. to 5 p.m.; no Sunday hours). But the Friday show is going to go later into the evening. We'll have some dinner food for sale. And I'll be presenting a seminar at 7 p.m. on workbenches. I'll be showing my new Roubo workbench plus some very cool workholding devices you haven't seen yet.

Then, at 8 p.m. we'll be having a big roundtable question-and-answer session with all the toolmakers. Expect some sparks to fly. Perhaps some leg wrestling and other feats of strength. If you attended last year's program, you know that things get out of hand when you throw all these people in a room.

Oh, one more thing: All of this is free. Just show up at our offices at 4700 E. Galbraith Road, Cincinnati, OH 45236 on either (or both) days.

And by the way, lots of attendees brought their families along last year. Cincinnati is a fun town for a weekend getaway. Later in the week I'll post some of my favorite things to do here and places to eat (do you like goetta? You will).

For more information, visit the Lie-Nielsen web site.

— Christopher Schwarz

Other Good Hand Tool Resources

•  John Economaki's crazy blog at Bridge City (bridgecitytools.com/blog)

• "Handplane Essentials" by Christopher Schwarz

• Andrew Lunn's blog at Eccentric Toolworks (eccentrictoolworks.blogspot.com)

• "The Complete Illustrated Guide to Sharpening" (Taunton) by Thomas Lie-Nielsen

Read detailed wood lathe reviews at Wood Lathes Online

Wood Lathe Buyer's Guide

Wood Lathe Buyer's Guide Advice on what to look for when buying a wood lathe. Whether you're looking for a starter lathe or a tool that will last you 50 years, this article provides some suggestions on what to look for.

Cheap Wood Lathes

Cheap Wood Lathes There are a number of benefits to moving up in price and quality range. You will get a larger lathe, which allows much more freedom and variety in the projects you can do and the pieces you can make and large lathes are heavier which reduces vibration.

Care of Wood Lathe Tools

Care of Wood Lathe Tools Well maintained wood lathe tools are very important in wood turning. This article provides tips on how to care for your tools and keep them sharp and in good condition.

About Wood Lathe Tools

About Wood Lathe Tools This article is all about what wood lathe tools should be used for different phases of a wood turning project. It explains the functions of roughing gouges, skew chisels and other tools.

More Wood Lathes for Sale

I recently came across a new site that is listing a bunch of new wood lathes for sale. I strongly suggest you check them out, they have a lot of good deals, and provide a lot of information on the lathes they're listing. A lot of sites are simply people making a big list of products and expecting you to dig through them to find the information you need, but this site lays it all out for you.

They list the bestselling wood lathes for sale, which is very helpful since in general they sell well because they are very good tools and nice deals. I recommend taking a look at that post if you're interested in a wood lathe, you'll probably find something you like, and if not there is a more complete listing available.

Wood turning has always been a great hobby of mine, but it can be difficult finding tools, and equipment. For whatever reason it seems like there are not a lot of places to shop online and the selection is not always great. However if you're careful and with a little effort there are some really good prices out there. A lot of the wood lathes for sale are offered at pretty significant discounts online compared to retail stores.

It's definitely very important to have the right tools for the job when it comes to woodworking, and wood turning is especially demanding on your equipment. Buying the right stuff will go a log way towards making sure you produce quality work, whatever your reasons are.

The most important choice you have to make is which wood lathe to buy. What size you need, what features are most important, how much do you want to spend. These are all questions that you should be asking yourself before you get started. Everyones requirements are a little bit different and it's important to know what yours are before you make a large purchase.

Make sure to read all the reviews you can find, and if at all possible try and test out a lathe before you hand over your money.

Good luck!

Blog about wood lathe shopping

I found a great blog on livejournal with some more tips on shopping for a wood lathe. It has a lot of really good information, and some helpful links that will make your purchasing decision that much easier.

As always it's best to be well informed on whatever product your thinking about buying whether it's a wood lathe or a computer the process and thinking is the same. Read all the reviews, compare prices, get peoples opinions, experts and enthusiasts. Everyone will have something to tell you, then filter out the noise and see what you have left.

In the end you're the one making the decision, but you can't make a good decision without some good information, and that's why it pays to be well read. Some good things to look for in a lathe are a cast iron body, your lathe should be heavy enough that it won't vibrate itself of your workbench, but not so heavy that you need a crane and a team of workers to move it. You should always look for good alignment between the heads, as this can save you a lot of trouble and poor results caused by un-centered centers.

Good luck to you on your quest!

Wood Lathes for Sale

I've been looking to buy a wood lathe for a month or so but I'm having a tough time deciding on what model to choose, and more importantly where to buy one. I've been looking online mostly comparing reviews and retailers.

Amazon.com seems to have a lot of good lathes available and the prices are very good compared to most of the stores around here. There is the issue of shipping costs, which i figure will be a lot for a lathe since they can weigh a lot, but that's a consideration for the future.

The websites for individual companies like Jet, PSI, Grizzly etc. are ok, but obviously kind of biased, and it's pretty tough to find good in depth reviews. This page lists a bunch of wood lathes for sale and I thought it was very good, they have a lot of popular models and some pretty good reviews, but I still haven't decided what I should do.

I'm probably going to end up buying a mini lathe since I'm mostly interested in small projects like pen turning and maybe some bowls, and also my shop doesn't have a lot of room for a big lathe. The extra flexibility of a larger tool would be nice but I really don't think I can justify the cost right now.

The thing I hate most about shopping for tools is going into stores, the people that serve are all inevitably sleezes that just want to hawk an expensive product on you to get a big commission or else teenagers that don't know anything and don't care about helping you. That's why I'm mostly looking online, because at least you can always look at the specs of the lathe and what other reviews are saying.

So far the top contender is the Jet 1014i, it seems like a good compromise between quality and price. It's not too expensive, but not so cheap that I would worry about it coming broken right out of the box, and all the reviews are very good. I'm also looking at a cheaper PSI model, and thinking of it more as a starter lathe that I would have to upgrade in a year or two. Lots of tough decisions.

The only thing I don't like about shopping online is that you can't get a good feel for the lathe, how it handles, whether the workmanship looks good etc. I'm thinking about going to stores to try them out and then making my final purchase online, but that just seems wrong for some reason. Oh well!